http://www.makingthings.com/forum Discuss & ask questions about MakingThings-related projects and products. hourly 1 2008-10-09T00:19:02Z http://www.makingthings.com/forum/development/debug-float-conversion/84034973/view I am having this issue where I get garbage out from the float. Even when converting to a char array: /debug/message È.V from USB (COM3)   Any help ... 2010-03-11T22:38:17Z Comment http://www.makingthings.com/forum/max-msp/338029810/986140173/view OK, I've got my make controller V2.0 all hooked up to max5 under osx 10.5.8 using Heavy 1.7 etc as per the latest instructions according to this forum (maybe ... 2010-03-10T16:10:20Z Comment http://www.makingthings.com/forum/max-msp/846575681/922025017/view OK, I've got my make controller V2.0 all hooked up to max5 under osx 10.5.8 using Heavy 1.7 etc as per the latest instructions according to this forum (maybe ... 2010-03-10T16:06:19Z Comment http://www.makingthings.com/forum/development/debug-float-conversion/168452164/view Any ideas where this jewel ran off too?   2010-03-09T19:53:57Z Comment http://www.makingthings.com/forum/devices/43830178/981951846/view Hi Dan,    I am using the DS18B20 and DS2438z sensors for temperature readings in a solar water heater project. I used the ... 2010-03-09T19:35:42Z Comment http://www.makingthings.com/forum/devices/43830178/830709573/view 2010-03-07T23:45:41Z Comment http://www.makingthings.com/forum/flash/418410809/555603796/view You may have a look at my findings regarding the pull-ups for outputs It is in the forum under hardware title : stepper and ethernet issues Port 0 active ... 2010-03-06T08:18:10Z Comment http://www.makingthings.com/forum/devices/43699827/179650646/view but I’m a C# programmer actually I’ve a very good experience using .Net languages like C# and VB. I would like to implement some automation to my house ... 2010-03-06T00:29:20Z Comment http://www.makingthings.com/forum/bugs-requests/375237162/401563639/view I am trying to decide what the best way would be to control a motor remotely and thought OSC would be a good method. So I followed the guide ... 2010-03-05T19:02:07Z Comment http://www.makingthings.com/forum/devices/110361545/822221465/view Further to the problems using stepper motors and using stepper motors with Ethernet I came across the following problem: I use 2 servo motors stepper 0 and ... 2010-03-05T16:39:31Z Comment http://www.makingthings.com/forum/flash/741202282/336783305/view can silverlight compete with adobe flash? which one is better for web design what are the pros and cons of each one 2010-03-05T10:15:19Z Comment http://www.makingthings.com/forum/flash/741202282/938473560/view web design 2010-03-05T10:12:37Z Comment http://www.makingthings.com/forum/development/520367001/817625817/view I just received my Make Controller Kit with the v2.0 Application board. I know notice that I will need more Input/Output ports than what is supplied on the ... 2010-03-05T06:18:52Z Comment http://www.makingthings.com/forum/devices/283932977/118457012/view I had the same issue a while ago. This sounds basic, but honestly, try this.... it worked for me after i was getting a connected "Green Light" on my ethernet ... 2010-03-03T20:55:55Z Comment http://www.makingthings.com/forum/devices/82827763/216112775/view I've just started using the MakingThings microcontroller kit v2.0.  I've followed all the steps to let Windows recognize the device.  The first time the ... 2010-03-03T20:40:03Z Comment http://www.makingthings.com/forum/devices/283932977/910378067/view I had the same problem recently. Are you running heavy.bin? 2010-03-03T17:12:32Z Comment http://www.makingthings.com/forum/devices/63333016/520563012/view first test with the driver is working :) the set up is a little simple max patch in which i trigger the signal so far tih the metro object in max/msp over ... 2010-03-02T15:29:57Z Comment http://www.makingthings.com/forum/project-discussion/32978084/179945284/view I know this is not an answer to your question but why on earth would you want anything other than your foot to have anything to do with controlling your ... 2010-03-01T08:56:31Z Comment http://www.makingthings.com/forum/bugs-requests/973180153/795232207/view Hello All, I am having trouble with my MC, likely with the USB driver.  When I erase the board and upload the latest version of heavy.bin (version 2) and ... 2010-03-01T02:22:38Z Comment http://www.makingthings.com/forum/devices/283932977/659614317/view Hi, all.  So, I'm trying to get busy on my project, linking up several items though an eternet hub.  At this point, I'm just trying to get everything to ... 2010-02-27T19:02:57Z Comment